Sizing & How-to

How to Calculate Chlorine Dosage for Any Tank Size

Chlorine dosing is simple arithmetic once you know three numbers: the tank volume, the strength of your bleach and the concentration you're aiming for. Here's the formula, ready-made tables and the checks that tell you it worked.

Updated 3 min read 4 sources cited
A hand adding a measured scoop of chlorine to a tank of water, with a chlorine bottle and a ppm test strip
The short answer

Bleach (mL) = Tank volume (L) × Target (mg/L) ÷ (Bleach strength % × 10). To shock-disinfect a cleaned tank at 50 mg/L for 24 hours, a 1,000-litre tank needs about 830 mL of 6% bleach (950 mL of 5.25%, 400 mL of 12.5%); then drain it away and refill. For routine treatment of drinking water, about 5 mg/L is a starting dose (83 mL of 6% per 1,000 L), aiming for at least 0.5 mg/L free chlorine after 30 minutes and never above WHO's 5 mg/L guideline in water you drink. Use plain, unscented bleach.

50 mg/L, 24 hshock disinfection of a cleaned tank (or 200 mg/L for 3 h)
≥ 0.5 mg/Lfree chlorine after 30 minutes for drinking water
5 mg/LWHO health-based maximum for chlorine in drinking water
On this page
  1. The formula
  2. Doses by tank size
  3. Shock-disinfecting a tank
  4. What changes the dose
  5. Common mistakes
  6. The bottom line

Most chlorination problems come from the arithmetic: the wrong bleach strength, gallons mixed with litres, or a shock dose used where a routine dose was meant. This guide gives the formula, ready-made tables and the checks.

The formula

Bleach doseBleach (mL) = Tank volume (L) × Target chlorine (mg/L) ÷ (Bleach strength % × 10)
US: fl oz = gallons × 3.785 × mg/L ÷ (strength % × 10) ÷ 29.57

Bleach strength × 10 is roughly the grams of chlorine per litre of bleach: 6% bleach carries about 60 g/L, so each millilitre adds 60 mg. The percentage is by weight, and bleach is slightly denser than water, so these doses err a little on the generous side.

Example: 2,000 L tank, 50 mg/L, 6% bleach: 2,000 × 50 ÷ 60 = 1,667 mL.

Doses by tank size

Shock disinfection, 50 mg/L (hold 24 hours, then drain):

Tank5.25% bleach6% bleach8.25% bleach12.5% liquid chlorine
1,000 L950 mL830 mL610 mL400 mL
2,000 L1.9 L1.67 L1.21 L800 mL
5,000 L4.8 L4.2 L3.0 L2.0 L
10,000 L9.5 L8.3 L6.1 L4.0 L
1,000 US gal122 fl oz107 fl oz78 fl oz51 fl oz

For a faster job, Minnesota's guidance allows 200 mg/L for 3 hours: four times these amounts.

Routine treatment, about 5 mg/L (water you'll use; test after 30 minutes):

Tank5.25% bleach6% bleach8.25% bleach12.5% liquid chlorine
1,000 L95 mL83 mL61 mL40 mL
2,000 L190 mL167 mL121 mL80 mL
5,000 L476 mL417 mL303 mL200 mL
10,000 L952 mL833 mL606 mL400 mL

For a single container of drinking water, use the US EPA's figure: 8 drops of 6% (or 6 drops of 8.25%) bleach per gallon, doubled for cloudy or cold water. The chlorine dosage calculator and the bleach to water ratio calculator work out other sizes.

Shock-disinfecting a tank

  1. 1

    Clean first

    Drain, remove sediment and scrub the walls. Dirt uses up chlorine and shelters germs. See sediment in your tank.

  2. 2

    Dose and fill

    Add the bleach as the tank fills so it mixes, then open each tap until you smell chlorine, so the pipes are dosed too.

  3. 3

    Hold

    24 hours at 50 mg/L, or 3 hours at 200 mg/L. Nobody drinks the water in this time.

  4. 4

    Drain away safely

    Drain away from septic systems, plants and waterways, then refill and flush the taps until the strong smell goes.

How chlorination of water tanks works covers the chemistry and when to shock-disinfect.

What changes the dose

  • Bleach strength and age. Check the label; bleach loses strength over months, faster in heat.
  • Dirt and slime. They consume chlorine; clean first, then test.
  • pH. Chlorine works best below about pH 8; at higher pH, more is needed for the same effect. See the water pH adjustment calculator.
  • Temperature. Cold water disinfects more slowly; allow the full contact time.

Common mistakes

  • Using the wrong bleach strength. 5.25%, 6%, 8.25% and 12.5% products need very different volumes.
  • Drinking shock-dosed water. 50 mg/L is ten times WHO's 5 mg/L guideline; drain it away.
  • Scented or "splash-less" bleach. Use plain, unscented bleach only.
  • Dosing a dirty tank. The chlorine is used up before it disinfects.
  • Not testing. A cheap free-chlorine test confirms the dose worked.

The bottom line

Bleach (mL) = litres × target mg/L ÷ (bleach % × 10). To shock-disinfect a cleaned tank, dose 50 mg/L and hold it for 24 hours (about 830 mL of 6% bleach per 1,000 L), then drain and refill. For water you'll drink, aim for at least 0.5 mg/L free chlorine after 30 minutes and stay under 5 mg/L. Check the bleach strength every time and test the result.

Frequently asked questions

How much bleach do I put in a 1,000-litre tank?

For shock disinfection at 50 mg/L: about 830 mL of 6% bleach, 950 mL of 5.25%, 600 mL of 8.25% or 400 mL of 12.5% liquid chlorine, held for 24 hours and then drained away. For routine treatment of drinking water at about 5 mg/L: about 83 mL of 6% bleach or 40 mL of 12.5%, then test for at least 0.5 mg/L free chlorine after 30 minutes.

How much bleach for a 1,000-gallon tank?

At 50 mg/L, about 122 fl oz (0.95 gallon) of 5.25% bleach, 107 fl oz of 6%, or 78 fl oz of 8.25%. That's a shock dose: drain and flush before using the water.

What's the difference between shock and routine chlorination?

Shock chlorination (50 mg/L or more) disinfects the tank and pipes after cleaning, repairs or contamination; the water is then drained away, not drunk. Routine chlorination adds a small dose to the water you'll use, aiming for at least 0.5 mg/L free chlorine after 30 minutes while staying under 5 mg/L.

Does the bleach strength on the label matter?

Yes. Household bleach is sold at about 5.25–8.25%, and pool or liquid chlorine at 10–12.5%. The dose scales directly with strength, so using the wrong figure can under- or over-dose by half or more. Bleach also weakens with age and heat.

How do I know the chlorination worked?

Test it. After a shock dose, a test should still show a strong chlorine residual at the end of the contact time; if it's gone, the tank had too much dirt and needs cleaning and redosing. For routine treatment, test for free chlorine after 30 minutes: at least 0.5 mg/L.

Sources and review

Doses, contact times and limits on this page come from these references; bleach volumes are calculated from the formula shown.

  1. Minnesota Department of Health — Storage tank disinfection. Disinfect at 50 mg/L for 24 hours or 200 mg/L for 3 hours, then drain away from the distribution and septic systems.
  2. enHealth — Guidance on the use of rainwater tanks. 40 mL of 12.5% liquid chlorine per 1,000 L; free chlorine of at least 0.5 mg/L after 30 minutes.
  3. WHO — Chlorine fact sheet (2022). Health-based guideline value of 5 mg/L; at least 0.5 mg/L free chlorine after 30 minutes' contact at pH below 8.
  4. US EPA — Emergency disinfection of drinking water. 8 drops of 6% or 6 drops of 8.25% bleach per gallon; double for cloudy or cold water; wait 30 minutes.
John Mac, PE
Licensed Professional Engineer (Texas) · Water Systems Specialist

John has spent 13+ years designing, sizing and fixing residential and light-commercial water storage systems across more than 180 tank projects. He writes and reviews every guide and calculator on WaterTankCalculator.com.

Published · Last reviewed